How a geeky bachelor gets laundry done

Let’s get this out of the way before I even get started: I do the laundry wrong.

That said, I don’t like wasting energy. Our electric company’s website has a tool that estimates your energy usage by category based on your responses to a questionnaire about what type of house you have, how many occupants, and what types of appliances you have. The questionnaire is sufficiently detailed to make me believe it presents a realistic picture of our energy use. It is an eye-opening look into where our electricity dollars go. After heating, water heating and laundry are the largest energy consumers in our house.

Within the category of water heating and laundry, the dryer is the second-largest consumer.

We already set the programmable thermostat to the lowest temperature we can tolerate, and the water heater is already set to the U.S. Department of Energy’s recommended 120°F. In my view, the next item that would have the most bang for the buck is to not run the dryer any more than necessary, so I take the clothes out before they start to get crispy. (Which brings me to my original acknowledgement: I do the laundry wrong. This post isn’t supposed to be about marital issues, so let’s move along.)

I thought, what if there is a happy medium? I know that there are dryers out there with moisture sensors that stop the dryer when the clothes are dry instead of just running until it hits the time you arbitrarily set at the beginning of the cycle. Since our dryer does not have a moisture sensor, perhaps I could build one.

Moisture sensors in fancier dryers have two metal strips in the drum that the clothes touch as they tumble around. Wet clothes are apparently slightly conductive, whereas dry clothes are not. By monitoring the electrodes, the dryer can determine when it is done. Since I do not have access to terminals like this, and I am unlikely to gain permission to hack up the dryer, I thought that a humidity sensor in the exhaust would be a good means to tell when the clothes are dry. I found an inexpensive humidity sensor at Sparkfun, and waited for a chance to experiment with it. With the rest of my family out of town, I have the perfect opportunity this week.

I placed the humidity and temperature sensors behind the dryer’s lint filter and connected them to the good old Arduino as a simple data logger, and then I captured humidity and temperature readings during the first load of laundry I did earlier this week. This is the humidity and temperature profile of a full 60 minute cycle (PDF, 16kB).

I learned a few things by examining the plot.

  • I thought that the heating element cycled on and off more. In reality, the heating element is on continuously for nearly 45 minutes, shown by the constantly rising temperature line. This makes sense, though, since it obviously takes a while to heat several pounds of clothes and all that extra water by 100°. Think about trying to boil a pot of water by pointing a hair dryer at it.
  • Once the load finally reaches the thermostat’s high trip point, apparently 155°, the temperature drops by 35° in 5 minutes to 120°, the thermostat’s low trip point, at which point, the heater comes on again. The difference between the trip points is called hysteresis. (Bonus word for the day. You come across this word a lot in control systems.)
  • I should listen carefully for the pop when the thermostat cycles the heating element off and take the clothes out immediately. This will maximize cat happiness when she lays down on the clothes as I try to fold them. (Using incorrect folding technique, of course. It’s okay, since the cat is fat enough to press out any wrinkles.)
  • The dryer apparently is designed to keep the heat element off during the last 5 minutes of the cycle in order to bring down the temperature of the clothes, presumably so they wrinkle less. You can see that the thermostat wants to turn the heat on at about 53 minutes, but the heater is turned off shortly afterward because the cycle will be ending soon. (By the way, what are wrinkles?)
  • The humidity of the exhaust air goes down as the cycle continues. Surprise! To me, this shows that merely sampling the humidity of the air coming out of the dryer doesn’t exactly say when the clothes are dry. Once the dryer finally got warmed up all the way, the humidity went to about 10% and stayed there. I know the clothes weren’t dry at 45 minutes, because they were just barely dry at 60 when the cycle ended, and the humidity was basically the same at those two points. (Okay, I admit it: I can tell when clothes aren’t fully dry.)
  • When the temperature line is rising, the heat element is on. For this load, the element was on for around 50 minutes. How much did the load cost in electricity use? 5600 W heater × 50 minutes = 4.67 kWh, or 47¢. I’m not sure exactly how big the motor is, probably 1/4 or 1/3 hp, so that probably brought the total to 50¢ for this load.

So, unfortunately, in this round, the humidity sensor I bought looks like it won’t useful in trying to minimize dryer use. But at least I got to teach the Arduino a new trick and to make a graph!

Taking a second look at the project, I noticed some omissions.

  1. I skipped over a detail of the humidity sensor’s datasheet specifying that I needed to place an 80kΩ load across the sensor output, so this may have affected the humidity readings.
  2. The load was really big, and the full 60 minute cycle did not get it completely dry. Perhaps a fully dry load does produce another significant drop in the humidity of the exhaust air.
  3. I should have weighed the laundry before and after running it through the dryer. How much water did it have to remove? Several pounds, or the better part of a gallon, probably.

I will have to try the experiment again later this week after making a couple changes.

David’s Lawn-mowing Efficiency Hierarchy’ — Planet Money Blog : NPR

I’m so glad I’m not the only one who thinks like this.

1. The most efficient way to mow is the spiral: start from the outside and do the border, spiraling in to the middle.

2. Next, you have the long stripes: mow the long edge-the length of the rectangle-and then u‑turn, and go back forth, striping the turf till you’re done.

3. Next, the short stripes: same as long stripes, but this time you’re going back and forth across the short distance.

4. Finally, the diagonal stripes: make strips starting at one corner, and going back and forth across the diagonal of the rectangle.Aesthetically, you’re going to want to dial this one to 45 degrees.

4b. The Old Man “Keep Off My Lawn You Darn Kids” Deluxe Double-Diagonal Stripes: Do method 4, then do it again so the diagonals crisscross. Recommended for baseball outfields.

David’s Lawn-mowing Efficiency Hierarchy’ — Planet Money Blog : NPR.

Regarding the podcast that the letter writer refers to, the “efficiency expert” sounds insufferable. I mean, there are parts of my life that I like to optimize. I take pride in packing the dish washer as tightly as possible. I have favorite lawn mowing patterns. I have a set pattern for the weekly chores. But lining up items in the bathroom in order of their use? At least this guy made a career out of his OCD tendencies.